NEW QUESTION 1
Refer to the exhibits.

Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN. Which two commands are missing? (Choose two.)

• A. The ip nhrp redirect command is missing on the spoke routers.
• B. The ip nhrp shortcut command is missing on the spoke routers.
• C. The ip nhrp redirect command is missing on the hub router.
• D. The ip nhrp shortcut command is missing on the hub router.
• E. The ip nhrp map command is missing on the hub router.

Answer: BC

NEW QUESTION 2
Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through
router R2. Which debug command is used to troubleshoot this issue?

• A. debug ip flow
• B. debug ip sla error
• C. debug ip routing
• D. debug ip packet

Answer: C

NEW QUESTION 3
Refer to the exhibit.

After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot
reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?

• A. Set the administrative distance 100 under the RIP process on R2.
• B. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
• C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
• D. Redistribute the directly connected interfaces on R2.

Answer: B

NEW QUESTION 4
Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: B

NEW QUESTION 5
Refer to the exhibit.

An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?

• A. Add the aaa authentication login default none command to the global configuration.
• B. Replace the capital “C” with a lowercase “c” in the aaa authentication login Console local command.
• C. Add the aaa authentication login default group tacacs+ local-case command to the global configuration.
• D. Add the login authentication Console command to the line configuration

Answer: D

NEW QUESTION 6
Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?

• A. NHRP
• B. IPsec
• C. MP-BGP
• D. OSPF

Answer: D

NEW QUESTION 7
Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns
the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

• A. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
• B. Route reflector setup requires full IBGP mesh between the routers.
• C. In route reflector setup, only classful prefixes are advertised to other clients.
• D. In route reflector setups, prefixes are not advertised from one client to another.

Answer: A

NEW QUESTION 8
What is a prerequisite for configuring BFD?

• A. Jumbo frame support must be configured on the router that is using BFD.
• B. All routers in the path between two BFD endpoints must have BFD enabled.
• C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.
• D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.

Answer: C

NEW QUESTION 9
Refer to the exhibit.

Which subnet is redistributed from EIGRP to OSPF routing protocols?

• A. 10.2.2.0/24
• B. 10.1.4.0/26
• C. 10.1.2.0/24
• D. 10.2.3.0/26

Answer: A

NEW QUESTION 10
Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: D

NEW QUESTION 11
Which statement about IPv6 ND inspection is true?

• A. It learns and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables.
• B. It learns and secures bindings for stateless autoconfiguration addresses in Layer 2 neighbor tables.
• C. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables.
• D. It learns and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables.

Answer: B

NEW QUESTION 12
Refer to the exhibit.

What is the result of applying this configuration?

• A. The router can form BGP neighborships with any other device.
• B. The router cannot form BGP neighborships with any other device.
• C. The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.
• D. The router can form BGP neighborships with any device that is matched by the access list named “BGP”.

Answer: D

NEW QUESTION 13
Which statement about MPLS LDP router ID is true?

• A. If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
• B. The loopback with the highest IP address is selected as the router ID.
• C. The MPLS LDP router ID must match the IGP router ID.
• D. The force keyword changes the router ID to the specified address without causing any impact.

Answer: B

NEW QUESTION 14
Refer to the exhibit.

A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

• A. The local preference value in another neighbor statement is higher than 250.
• B. The local preference value should be set to the same value as the weight in the route map.
• C. The route map is applied in the wrong direction.
• D. The weight value in another statement is higher than 200.

Answer: D

NEW QUESTION 15
An engineer configured the wrong default gateway for the Cisco DNA Center enterprise interface during the install. Which command must the engineer run to correct the configuration?

• A. sudo maglev-config update
• B. sudo maglev install config update
• C. sudo maglev reinstall
• D. sudo update config install

Answer: A

NEW QUESTION 16
Which command allows traffic to load-balance in an MPLS Layer 3 VPN configuration?

• A. multi-paths eibgp 2
• B. maximum-paths 2
• C. maximum-paths ibgp 2
• D. multi-paths 2

Answer: B

NEW QUESTION 17
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 18
Refer to the exhibit.

Which configuration denies Telnet traffic to router 2 from 198A:0:200C::1/64?

• A. Option A
• B. Option B
• C. Option C
• D. Option D

Answer: A

NEW QUESTION 19
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 20
Refer to the exhibit.

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the
configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

• A. Use an extended access list instead of a standard access list.
• B. Change sequence 10 in the route-map command from permit to deny.
• C. Use a prefix list instead of an access list in the route map.
• D. Add this statement to the route map: route-map RM-OSPF-DL deny 20.

Answer: B

NEW QUESTION 21
Refer to the exhibit.

ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to
achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?

• A. Start-time 00:00
• B. Start-time 0
• C. Start-time immediately
• D. Start-time now

Answer: D

NEW QUESTION 22
Drag and drop the DHCP messages from the left onto the correct uses on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 23
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 24
......