NEW QUESTION 1
A domain ID conflict is detected on a switch. Which action resolves the issue in the shortest possible time after the preferred domain ID is changed to a static domain ID?

• A. Issue an fcdomain disruptive restart.
• B. Issue an fcdomain nondisruptive restart.
• C. Enter the commands for a VSAN suspend / no-suspend.
• D. Enter the commands to complete a domain manager fast restart.

Answer: A

NEW QUESTION 2
Which action must be performed to deactivate a VSAN without losing its configuration?

• A. Isolate it.
• B. Delete it.
• C. Rename it.
• D. Suspend it.

Answer: D

NEW QUESTION 3
A network engineer is configuring a Cisco MDS switch for FCoE. Which two conditions must be considered during the implementation phase? (Choose two.)

• A. On Cisco MDS switches, system-defined class maps for class-FCoE and class-default are enabled but can be deleted.
• B. The QoS policy must be identical to other Cisco FCoE switches in the network.
• C. On the Cisco MDS, the MTU is set equal to 2112.
• D. VLAN 1 or the native VLAN can be mapped to an FCoE VSAN.
• E. FCoE is already enabled on a Cisco MDS switch.

Answer: BE

NEW QUESTION 4
Refer to the exhibit.

What is the result of the configuration?

• A. No-drop CoS values are advertised by the DCBX.
• B. LFC is prioritized over PFC on Ethernet 1/10.
• C. PFC operates on Ethernet 1/10 regardless of the capability of the peer.
• D. PFC fails to operate properly unless LFC is disabled on Ethernet 1/10.

Answer: A

NEW QUESTION 5
Refer to the exhibit.

Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?

• A. device-alias mode
• B. session
• C. qos
• D. smart-zoning

Answer: A

NEW QUESTION 6
DRAG DROP
Drag and drop the DCNM configuration tasks from the left onto the correct tools on the right.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

NEW QUESTION 7
Which condition requires using a device alias rather than a Fibre Channel alias?

• A. The zone database must be distributed over the fabric.
• B. The same alias must be used in zoning as well as DPVM.
• C. All aliases being used are being configured in the same VSAN.
• D. Aliases must be saved within a central database on the fabric.

Answer: A

NEW QUESTION 8
Which component is initially responsible for loading the kickstart image on Cisco MDS Switches?

• A. ROMMON
• B. BIOS
• C. NX-OS
• D. BASH

Answer: C

NEW QUESTION 9
Refer to the exhibit.

Which command is used to determine which switch has the lock?

• A. show zoneset active
• B. show zone status
• C. show flogi database

Answer: C

NEW QUESTION 10
A storage administrator is upgrading Cisco NX-OS on a Cisco MDS switch. The administrator performs an ISSU upgrade following the configuration guide. While the install is proceeding, the administrator connects a new server to the switch, which cannot access storage. The existing servers continue to operate properly through the switch. Why is the new server failing to connect?

• A. The fabric data plane resets as part of the upgrade process.
• B. The new server is unable to log in to the fabric to receive an FC-ID.
• C. The upgrade process disables any currently unused ports.
• D. The zoning database is locked during the upgrade process.

Answer: D

NEW QUESTION 11
Refer to the exhibit.

A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?

• A. per packet, balanced between interfaces fc1/9 and fc1/10
• B. from interface fc1/9
• C. from interface fc1/10
• D. per flow, balanced between interfaces fc1/9 and fc1/10

Answer: D

NEW QUESTION 12
A storage network engineer is implementing disk-array data replication between two SAN environments in two different data centers not connected via Fibre Channel. Which SAN switch feature must be implemented?

• A. FCIP
• B. zoning merge over LAN
• C. VSAN scoping
• D. IVR

Answer: A

NEW QUESTION 13
Which feature on MDS platforms ensures that the code that is running on the hardware platform is authentic and unmodified, while also validating the BIOS to eliminate any rootkits.

• A. Cisco Secure Boot
• B. UEFI Secure Boot
• C. Secure Unique Device Identifier
• D. BIOS Secure Boot

Answer: A

NEW QUESTION 14
Which two components are required for successful MDS USB POAP (Choose two.)

• A. NTFS formatted USB drive
• B. USB drive in port 1
• C. script named poap_script pl
• D. ENTERPRISE_PKG license
• E. system and kickstart images

Answer: CE

NEW QUESTION 15
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?

• A. Add the received ID to the allowed list.
• B. Configure a static domain on the subordinate switch and reboot the switch.
• C. Enable the FICON feature on the affected VSAN.
• D. Configure IVR NAT on the affected VSAN.

Answer: A

NEW QUESTION 16
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules. The install command is executed on the standby supervisor module but fails. Which action would have prevented this failure?

• A. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
• B. The upgrade must be done on the active supervisor module only.
• C. Cisco Fabric Services must be disabled before starting the upgrade.
• D. Fabric Controller Service must be stopped before starting the upgrade.

Answer: B

NEW QUESTION 17
A storage network engineer is implementing a port channel for multiple FCIP interfaces with write acceleration in a client’s storage network. Which channel mode must be used?

• A. on
• B. passive
• C. active
• D. force

Answer: C

NEW QUESTION 18
A storage network engineer must configure a 48-port Cisco MDS switch to reject any login requests to VSAN 10 from unauthorized Fibre Channel devices and switches. All the devices that were already logged in to the switch from this VSAN must be allowed without any manual configuration. Which configuration must be applied?

• A. switch(config)# feature port-security switch(config)# port- security activate vsan 10
• B. switch(config)# feature port- security switch(config)# port-security activate vsan 10 no auto- learn
• C. switch(config)# feature port-security switch(config)# port-security database vsan 10 switch(config-port-security)# any-wwn interface fc1/1 – fc1/48
• D. switch(config)# port-security activate vsan 10

Answer: D

NEW QUESTION 19
Which command identifies the application and the user that have a Cisco Fabric Services session open?

• A. show cfs application
• B. show zoneset active
• C. show cfs lock
• D. show device-alias database

Answer: A

NEW QUESTION 20
Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?

• A. The license can be reassigned when a switch is replaced with a newer version within the same product family.
• B. The license can be assigned to either server MAC address or switch serial number.
• C. An unlimited number of devices can be added to the list of licensed devices.
• D. The license can be reassigned when the switch is replaced with a Cisco Nexus switch.

Answer: A

NEW QUESTION 21
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?

• A. show telemetry pipeline stats
• B. show telemetry transport
• C. show telemetry control stats
• D. show analytics system-load

Answer: B

NEW QUESTION 22
A storage administrator manually configures a storage switch to use a new static domain ID. After issuing an fcdomain restart vsan 1 command, the administrator sees that the switch is still using the existing domain ID. What is the reason why the configuration is not working?

• A. Static domain IDs apply only after a switch is rebooted.
• B. The disruptive keyword was not used on the command.
• C. Build fabric notifications were not sent to the other switches.
• D. Domain manager fast restart is not enabled on the switch.

Answer: A

NEW QUESTION 23
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?

• A. The autoreconfigure option is disabled on both switches.
• B. The autoreconfigure option is enabled on both switches.
• C. The rcf-reject option is enabled on the interfaces.
• D. The rcf-reject option is disabled on the interfaces.

Answer: A

NEW QUESTION 24
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

• A. MDS(config)# interface fc 1/1MDS(config-if)# fcsp esp manual
• B. MDS(config)# fcsp esp manual
• C. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp mode gcm MDS(config-if-fcsp)# fcsp esp manual
• D. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual MDS(config-if-fcsp)# mode gcm

Answer: A

NEW QUESTION 25
......