NEW QUESTION 1

Which statement about the show chassis hardware Command is correct?

• A. The command provides a list of installed hardware components, including serial numbers and model numbers.
• B. The command provides a list of all current hardware utilization statistics and operational status
• C. The command provides 2 list of supported hardware components and their current operating status
• D. The command provides a list of supported hardware components and environmental thresholds.

Answer: A

NEW QUESTION 2

Click the Exhibit button.

You configured the route filter shown in the exhibit.
In this scenario, which IP addresses would term-One accept?

• A. IP addresses that are part of the 172.35.0.0/16 network and IP addresses that are in the 172.35.0.0/16 and 172.36.0.0/16 subnets.
• B. IP addresses that are part of the 172.35.0.0/16 network only.
• C. IP addresses that are part of the 172.35.0.0/16 network and IP addresses that are in the subnets of 172.35.0.0/16 network.
• D. IP addresses that are part of the 172.35.0.0/16 network, but not IP addresses that are part of the 172.35.0.0/16 network itself.

Answer: C

NEW QUESTION 3

Which command allows you to verify the syntax and consistency of your configuration
without actually activating your configuration?

• A. User Interfaces
• B. commit verify
• C. commit check
• D. check commit
• E. commit no-activate

Answer: C

NEW QUESTION 4

Click the Exhibit button.

The next hop identified in the static route command is not directly connected to your router. Referring to the exhibit, what must be added to the command for the static route to work?

• A. retain
• B. resolve
• C. readvertise
• D. install

Answer: B

NEW QUESTION 5

What information would you find using the CLI help function? (Choose two.)

• A. tip of the day
• B. Junos technical publications
• C. explanation of specific system log error messages
• D. explanation of traceoption events

Answer: AC

NEW QUESTION 6

A packet enters a Junos device. No matching destination entry exists in the forwarding table. How will the device respond?

• A. The RE responds to the source with a destination unreachable notification message
• B. The PFE responds to the destination with a source unreachable notification message
• C. The PFE responds to the source with a destination unreachable notification message
• D. The RE responds to the destination with a source unreachable notification message

Answer: B

NEW QUESTION 7

What would you use as a network tool to open a secure terminal connection from a device running Junos OS to another device?

• A. SSH
• B. HTTPS
• C. RDP
• D. telnet

Answer: A

NEW QUESTION 8

You issue the request system zeroize command. Which statement is correct in this scenario?

• A. All data files are deleted and all configuration setting are returned to factory defaults.
• B. All data files remain unchanged but all configuration setting are returned to factory defaults.
• C. Disk space is freed by rotating log files and a proposed list of files to delete is presented.
• D. All data files are deleted and the configuration settings remain unchanged.

Answer: A

NEW QUESTION 9

Which routing table is used for multicasting forwarding cache?

• A. Inet.3
• B. Inet.0
• C. Inet.1
• D. Inet.2

Answer: C

NEW QUESTION 10

What happens when a route does not match any user-configured policies?

• A. The route is rejected.
• B. The route is accepted.
• C. The route is given a lower priority.
• D. The route is sent to the default policy.

Answer: D

NEW QUESTION 11

What’s is the minimum system-defined user class required to issue clear commands?

• A. read-only
• B. operator
• C. authorized
• D. super-user

Answer: B

NEW QUESTION 12

You are connected to your Junos device using an SSH connection to the fxp0 interface. No other interface are currently configured beyond their default setting. You commit a configuration that makes the fxp0 interface unreachable from your management network. In this scenario, how would you re-establish communication with the device?

• A. Unplug the network cable and plug it back in.
• B. Power off and power on the device.
• C. Establish an SSH connection to the loopback interface.
• D. Connect to the console of the device.

Answer: D

NEW QUESTION 13

Which protocol is responsible for learning an IPv6 neighbor's IMAC address?

• A. Neighbor Discovery Protocol (NDP)
• B. Media Access Control Security (MACsec)
• C. Address Resolution Protocol (ARP)
• D. Network Address Translation (NAT)

Answer: A

NEW QUESTION 14

The IP address 10.1.1.1 belongs to which class of IP address space?

• A. Class A
• B. Class B
• C. Class C
• D. Class D

Answer: A

NEW QUESTION 15

Which two platforms are supported in physical and virtual form factors? (Choose two.)

• A. NFX Series
• B. SRX Series
• C. MX Series
• D. ACX Series

Answer: BC

NEW QUESTION 16

Click the Exhibit button.

A user attempts to log in to a Junos device. but the RADIUS server is unreachable. Referring to the exhibit, what is the default action of a Junos device in this scenario?

• A. The Junos device retries every 30 seconds until the connection is restored.
• B. The Junos device uses the local authentication database.
• C. The Junos device displays a RADIUS connection error.
• D. The Junos device prompts for a cached RADIUS password.

Answer: C

NEW QUESTION 17

Exhibit:

Which statement is true about the command shown in the exhibit?

• A. There needs to be a ; after top for the command to be accepted as a valid command.
• B. Only top should be used, no other options are allowed on the same line.
• C. The command shown in the exhibit would be accepted as a valid command.
• D. If you replace top with up command, it becomes valid.

Answer: C

NEW QUESTION 18

Which two interfaces are considered as physical interface? (Choose two.)

• A. xe-1/1/1
• B. ge-2/0/2.0
• C. et-5/0/0
• D. ae1.1

Answer: AB

NEW QUESTION 19
......