NEW QUESTION 1

Referring to the exhibit, which two actions would you perform to ensure that each host has valid multipathing? (choose two)

• A. Verify that the VLANs are properly configured on the switches
• B. Verify that the VLANs are properly configured on the ONTAP cluster
• C. Verify that ALUA is enabled on the switches
• D. Verify that ISCSI service is started on the ONTAP cluster

Answer: AB

Explanation:
Iscsi is already started, we can not run those commands successfully if the protocol is not started ALUA is enabled on hosts, It is not enabled on switches
VLANs are configured on the Netapp and switches, they need to be properly configured on both sides to work correctly
You can find more information on this link:
https://docs.netapp.com/ontap-9/index.jsp?topic=%2Fcom.netapp.doc.dot-cm-nmg%2FGUID-52AE6E9C-13B6

NEW QUESTION 2

What is the recommended minimum of data LIFs per node for iSCSI in a dual-fabric configuration with four SVMs?

• A. 8
• B. 12
• C. 16
• D. 4

Answer: A

Explanation:
Reference: https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sanconf/GUID-650DC466-CA3F
FCEEB52E7.html (6th bullet)

NEW QUESTION 3

During testing, an administrator notices that the wrong subsystem was returned using the NVMe discover command. The administrator was expecting test0_subsystem as the subsystem
Referring to the exhibit, what would cause the discrepancy?

• A. The wrong NQN was mapped to the subsystem
• B. The wrong WWPN was used in the discovery command
• C. Asymmetric Namespace Access (ANA) was not properly configured
• D. The NVMe was not configured on the test0 SVM

Answer: A

Explanation:
We can discard that ANA was not properly configured becase this is not a problem about multipathing. We can discard WWPN because this is an NVMe configuration where WWPN is not involved
We can discard that NVMe was not configured because we wouldn't be able to even run that command if that's true
Configure the NQN correctly is one of the steps when we configure NVMe You can find more information on this link:
http://senthil-it-infrastructure.blogspot.com/2020/05/netapp-ontap-97-nvme-configuration-and.html

NEW QUESTION 4

You want to access and mount a Linux L.UN using only iSCSl. In the past, the LUN ha;; been accessed using FC. What must you do to accomplish this task?

• A. Change the LUN protocol type to (SCSI.
• B. Create a new iSCSI igrou
• C. and change the LUN mapping from the original to the new igroup.
• D. Create a new iSCSI Igroup and map the LUN to both the new and existing FC igroup.
• E. Add an iSCSI protocol type to the existing igroup so that the LUN can be accessed by both FC and iSCSI hosts.

Answer: B

NEW QUESTION 5

Which data collection tool would be used for obtaining detailed information about hosts that are attached to ONTAP storage?

• A. Upgrade Advisor
• B. OneCollect
• C. Brocade Network Advisor
• D. Conflg Advisor

Answer: B

NEW QUESTION 6

For which two purposes would the use of VLAN's be beneficial? (Choose two.)

• A. to isolate iSCSI traffic from LAN/WAN traffic
• B. to separate LAN from WAN traffic
• C. to isolate management traffic from other IP traffic
• D. to isolate UDP from TCP traffic in the IP network
• E. to isolate SSH traffic from other IP traffic

Answer: AC

NEW QUESTION 7

You create a 20 GB LUN in a newly created 100 GB FlexVol volume. You then write 5 GB of data to the LUN. You have space reservation disabled on the LUN.
In this scenario, how much space do you have left on the volume?

• A. 95 GB
• B. 80 GB
• C. 75 GB
• D. 85 GB

Answer: A

Explanation:
Reference: https://library.netapp.com/ecmdocs/ECMP1368017/html/GUID-0E0B085C-5A42-43F3-9CCD- 4FD699BA6C89.html

NEW QUESTION 8

Exhibit.

The VMware ESX host discovers only two of four paths to a LUN on a new ONTAP cluster. Referring to the exhibit, which statement Is correct?

• A. The fabric zoning configuration does not allow access to the target LlFs.
• B. The igroup does not contain th
• C. WWPN of one initiator.
• D. The fabric name server is disabled.
• E. The initiator HBA is not connected to the fabric.

Answer: D

NEW QUESTION 9

Which two features does Assymmetric Namespase Access (ANA) support? (Choose two.)

• A. multipathing
• B. LUN masking
• C. LUN hosting
• D. path management

Answer: AD

NEW QUESTION 10

What does the space allocation argument in a lun create command do?

• A. It thick provisions the LUN.
• B. It only disables space reclamation (or the LUN.
• C. It thin provisions the LUN,
• D. It enables or disables space reclamation for the LUN

Answer: D

NEW QUESTION 11

Which statement is correct regarding virtual machine alignment on VMware ESX?

• A. RDM LUNs do NOT suffer from alignment problems because they are accessed directly by VMs.
• B. A VMFS LUN with a LUN type of VMware, will always have properly aligned VMs.
• C. Alignment issues can occur on any protocol including FCP, iSCSI, FCoE, and NFS
• D. msinfo32 or mbrscan can be run for the ESX service console to check for proper alignment of VMs.

Answer: C

NEW QUESTION 12

Exhibit.

Referring to the exhibit. What are two viable scenarios to test LUN multipathing on Host 1? (Choose two.)

• A. Reboot one of the switches.
• B. Disable one of the FC LIFs on Controller 1.
• C. Disconnect one of the host cables.
• D. Reboot Host 1.

Answer: AC

NEW QUESTION 13

A customer has multiple host applications that require FC block storage. You need to gather and validate the customer’s requirements for a supported NetApp solution.
Which two tools would be used to accomplish this task? (Choose two.)

• A. Interoperability Matrix Tool (IMT)
• B. OneCollect
• C. Config Advisor
• D. Hardware Universe (HWU)

Answer: AD

Explanation:
Reference: https://www.netapp.com/us/technology/interop.aspx

NEW QUESTION 14

An administrator is planning a hardware refresh and data migration from a Data ONTAP 7.3 system to new AFF A3-00 cluster that is using ONTAP 9.0. The Mode system only serves FC LUNs to a Windows 2012Rs server cluster that needs to remain connected after migration Referring to the scenario, which method would be used for the LUN migration.

• A. Unified Host Utility Kit
• B. 7-Mode Transition Tool (7MIT)
• C. Foreign LUN import (FLI)
• D. Oncommand system Manager

Answer: B

NEW QUESTION 15

Exhibit.

You need to configure the SnapCenter Plug-in for VMware vSphere to back up and restore VMware datastores.
Referring to the exhibit, which additional LIF type should you create before you configure the plug-in?

• A. intercluster
• B. node management
• C. SVM management
• D. cluster management

Answer: C

NEW QUESTION 16

Click the Exhibit button.

An administrator is trying to configure a multiple-hop Cisco MDS switch and is receiving the error shown in the exhibit.
In this scenario, which action will solve this problem?

• A. Configure the physical link of interface ext17 as an F_Port.
• B. Configure the external interface to a different virtual SAN (VSAN) on both ends.
• C. Connect the external link to a Cisco MDS switch.
• D. Turn N_Port ID virtualization (NPIV) off.

Answer: C

Explanation:
Reference: https://www.cisco.com/en/US/products/ps5989/ prod_troubleshooting_guide_chapter09186a00808c82f1.html

NEW QUESTION 17

You are configuring a 4-node AFF A400 ONTAP 9.8 cluster. The data center switches have limited ports, and you are given one 10-Gigabit Ethernet port per node for external access.
In this scenario, which three protocols share the same physical port? (Choose three)

• A. NVMe/FC
• B. ISCSI
• C. FCoE
• D. Snapmirror
• E. FC

Answer: BCD

Explanation:
If we have only ethernet switches available, we can only enable protocols over ethernet such as FCoE, ISCSI and Snapmirror.
NVMe/FC and FC need a SAN Fabric switch to work.

NEW QUESTION 18

Click the Exhibit button.

You are implementing an ONTAP 9.5 AFF A300 SAN cluster with the NVMe, FC, and FCoE protocols. Referring to the exhibit, which three protocols and physical port pairs are supported? (Choose three.)

• A. NVMe on ports 2a/2b
• B. FC on ports 2a/2b
• C. NVMe on ports 0e/0f
• D. FCoE on ports 0e/0f
• E. FC on ports 0e/0f

Answer: BCD

NEW QUESTION 19

Your server administrator upgraded a Windows 2016 Server from 16 Gb to 32 Gb HBAs. The application owner is now reporting slower performance to the AFF A700.
Which two actions will help troubleshoot performance on the server? (Choose two.)

• A. Verify the HBA model using Hardware Universe.
• B. Verify the HBA firmware using the Interoperability Matrix Tool.
• C. Confirm that LUN mapping exists.
• D. Confirm that Windows Host Utilities Is installed.

Answer: AB

NEW QUESTION 20

You will be purchasing two high availability NetApp AFF A700s systems. You want to set up a 4-node cluster. Which switch would you use for the cluster interconnect switches?

• A. NetApp CN1610
• B. Cisco Nexus 3132Q-V
• C. Cisco Nexus 5548UP
• D. Cisco Nexus 5020

Answer: B

NEW QUESTION 21
......